HPE ProLiant MicroServer Gen11 review: a compact server for a small office
Servix technical team · Updated
In brief. MicroServer Gen11 is HPE's smallest server: a tower for four 3.5-inch drives, a Xeon E-2400 processor, built-in iLO and two PCIe slots. Its niche is a branch, a small office, a test bench. Two limitations need to be accepted up front: there is no drive hot swap (replacing a drive means shutting down the server) and the entire network is four gigabit ports; a ten-gigabit adapter is installed separately. If these two points are a deal-breaker, look at the rack DL320 Gen11 (41,000,000 UZS) or the tower ML30 Gen11 (31,000,000 UZS) — they have both a hot-swap cage and a proper RAID controller. The rack alternative is analyzed in the DL320 Gen11 review.
HPE has updated its smallest server: the popular ProLiant MicroServer Gen10 Plus has been replaced by Gen11. It is a compact tower for a small office, a branch, a home lab or storage tasks — where a full rack is overkill, but reliability and remote management are already needed. We look at what has changed, where the machine's limits are and when it is better to choose something else instead.

HPE ProLiant MicroServer Gen11 — front view
What's inside
- Processor. Intel Xeon E-2400 (up to 8 cores, LGA1700 socket). Entry configurations come with lower-end CPUs, but the board also supports higher models such as the E-2436 — an upgrade gives a noticeable performance boost.
- Memory. DDR5 with error correction. For the tasks MicroServer is bought for, capacity is almost always limited not by the platform ceiling but by the budget: plan it for the workload right away, since adding modules in a compact chassis is inconvenient.
- Drives. Four 3.5″ SATA bays with tool-less mounting. There are also M.2 slots for a boot or caching SSD — using them for the hypervisor is better than occupying one of the four bays.
- Network. Four 1GbE ports on a Broadcom controller.
- Ports. Front: 2× USB 3.2 Gen2 (10 Gbps); rear: 4× USB, VGA and DisplayPort, a serial port and a dedicated iLO port.
- Expansion. Two low-profile PCIe slots (Gen10 Plus had one) plus MCIO and OCP service connectors on the board. The redesigned rear panel is the main practical improvement of this generation.
- Cooling and power. One rear fan and a compact internal power supply; the chassis is slightly larger than its predecessor.
What's missing: hot swap and what it means in a branch
MicroServer has no hot-swap backplane — this is a deliberate cost saving, and it has consequences that are better considered before the purchase rather than after the first drive failure.
- Replacing a drive means shutting down the server. In a branch 300 kilometers from Tashkent, this means sending an engineer and agreeing on a maintenance window, not “pull it out and plug it in”.
- RAID 5 on four drives becomes riskier. While you are on your way to replace the drive, the array runs without redundancy. If roads and timelines are unpredictable, RAID 6 on four drives is the wiser choice (half the capacity remains, but it survives two failures), or RAID 10.
- A cold spare drive on site is a must. Since there will be downtime anyway, let it last half an hour rather than two weeks of waiting for delivery. The drive must be the same model and capacity.
For a test bench or a home lab, none of this matters. For a production node in a branch, this is the main criterion when choosing between MicroServer and ML30 Gen11, which has a hot-swap cage.

MicroServer Gen11 drive bay
Networking: why four gigabits are not four gigabits
Four 1GbE ports look solid until you start doing the math. One gigabit port delivers about 110 MB/s of real throughput. A typical 3.5-inch drive reads at 150–200 MB/s, and an array of four drives considerably more. In other words, the bottleneck is not in the drives but in the network, and right away.
Combining ports into an aggregated link does not solve the problem the way one would like: LACP distributes sessions across ports rather than speeding up a single one. A user copying a large file will still get their 110 MB/s — it is just that another user next to them can get the same in parallel. For a file server for 15 people, this is enough. For nightly backups, image restores or video work, it is not.
The practical takeaway: if the task includes the word “backup” or “video”, put a 10GbE adapter into one of the two PCIe slots right away, not “later, if needed”. Also check whether the branch switch has a 10 Gbps port — otherwise the adapter will be limited by it.
How to build RAID without a hardware controller
The base configuration of MicroServer does not include a full RAID controller with cache and battery. There are three options, and the choice depends on what system will run on top.
- The platform's built-in SATA controller with software RAID. Free, configured in UEFI, and it works. The downside is that if the motherboard fails, the array is tied to the specific platform, and RAID 5 write performance without cache is noticeably lower than with a hardware controller.
- Operating system tools. Storage Spaces in Windows Server, mdadm or ZFS in Linux. The array can be moved to other hardware as a whole, diagnostics are more transparent, and ZFS also checks data integrity. Requires an administrator who knows how to do this.
- A PCIe controller in one of the two slots. Solves the performance and portability issue but takes a slot — and there are only two slots, and you have most likely already given one to 10GbE. You will have to choose.
How RAID levels behave on drives of different capacities and why RAID 5 on large drives is a bad idea today is covered in a separate article on RAID and the server disk subsystem.
iLO: what the basic license gives and what it does not
The built-in HPE iLO is the key advantage over self-built systems and consumer NAS: remote power on and off, hardware monitoring, failure logs, firmware updates without physical presence. A separate iLO network port lets you move management to a service network.
But there is a catch that leads to disappointment: the remote graphical console and virtual media are features of the advanced iLO license, not the basic one. The basic license provides monitoring and power control, and that is enough to “reboot a hung server”. But installing an operating system from an ISO image over the internet without traveling to the branch is not possible without the advanced license. For a remote site, this license pays for itself with the very first avoided trip — include it in the budget right away.

Tool-less drive bay latch
What to compare with: MicroServer, ML30 Gen11 and DL320 Gen11
Parameter | MicroServer Gen11 | ML30 Gen11 | DL320 Gen11 |
|---|---|---|---|
Chassis | compact tower | tower, full-size | 1U rack |
Processor | Xeon E-2400 | Xeon E-2400 | Xeon Scalable |
Drive hot swap | no | available in configurations with a hot-plug cage | yes |
PCIe slots | 2, low-profile | more, full-size | depends on the riser |
Placement | on a shelf, in a cabinet, under a desk | in a room without a rack | rack only |
Catalog price | made to order |
In terms of serviceability, the difference between MicroServer and ML30 is fundamental. MicroServer wins where there is physically no room for a normal-size tower or where quiet in the office matters. If there is no such constraint, ML30 Gen11 usually turns out to be the more sensible choice.
Typical branch scenarios
- File server and domain controller for 10–20 people. The main and most successful scenario: the load is light, a gigabit per user is enough, and iLO covers remote maintenance.
- 1C for a small department. Xeon E-2400 with its high core clock suits 1C well — for this platform, clock speed matters more than core count. The limitations are memory and the lack of a fast network if the database is on the same server and users work through a terminal.
- Backup storage. A workable option provided there is a ten-gigabit adapter: otherwise the nightly backup window will hit the gigabit limit and the backup will not finish in time.
- Video surveillance — with caveats. Four 8 TB drives in RAID 6 give about 16 TB of usable capacity: for sixteen 4 MP cameras in H.265, that is roughly twenty-four days of archive. You need to calculate this in advance, and for a serious system it is better to take a separate platform — how this is done is covered in the selection server for video surveillance.
Pros and cons
Pros | Cons |
|---|---|
Compact, well-built chassis, quiet operation | Only 4×1GbE — a separate 10GbE adapter is needed under load |
Two PCIe slots and a redesigned rear panel | No drive hot swap |
Built-in iLO for remote management | Remote console requires the advanced iLO license |
Xeon E-2400 with a CPU upgrade option | Intel only; there is no AMD EPYC alternative in the line |
Four 3.5″ bays and M.2 slots for the system | Price higher than “home” NAS with comparable components |
What to check before buying
- Who can physically get to the server to replace a drive, and how quickly — this determines the RAID level and whether a cold spare drive is needed on site.
- Whether remote operating system installation is needed: if so, include the advanced iLO license in the budget right away.
- Whether the branch switch has a free 10 Gbps port, if an adapter is planned.
- Where the hypervisor will go: on M.2, not in one of the four drive bays.
- Whether the task fits into four drives for the entire service life — unlike rack models, MicroServer has no room to expand.
- Whether there is a UPS: a compact chassis does not cancel power requirements, and outages in branches happen more often than in the head office.
MicroServer Gen11 is not about maximum performance but about a reliable compact node with real server management. We will select a configuration for the task — with the right processor, memory, drives and, if needed, a 10GbE adapter and an iLO license — and tell you honestly if ML30 or DL320 is the better deal in your case. Write to us; the full Gen11 line with prices is here.
Source and photos: ServeTheHome, Patrick Kennedy, 24.07.2025 — servethehome.com. Published with attribution.
Questions and answers
Can drives in MicroServer Gen11 be hot-swapped?
No. This model has no hot-swap backplane; replacing a drive requires shutting down the server. This is the main difference from ML30 Gen11 and rack ProLiant models, and the main argument against MicroServer for remote sites without permanent staff.
Are four gigabit ports enough?
For a file server for 10–20 people — yes. For backups, video work or image restores — no: one port gives about 110 MB/s, and link aggregation speeds up parallel sessions, not a single one. For such tasks, a 10GbE adapter is installed in a PCIe slot.
How does MicroServer differ from a regular NAS?
By its server platform: error-correcting memory, built-in iLO with a separate network port, support for server operating systems and hypervisors, warranty and spare parts supply channels. A NAS wins on price and ready-made out-of-the-box software; MicroServer wins on manageability and predictability in a corporate environment.
What to choose instead of MicroServer if hot swap is needed?
ML30 Gen11 for 31,000,000 UZS if the server will stand in a room without a rack, or DL320 Gen11 for 41,000,000 UZS if there is a rack. Both models use the same processor base or a higher-end one, but have a proper drive cage and a full RAID controller in their configurations.
Is the advanced iLO license needed?
If the server is located in another city — yes. The basic license lets you reboot it and see the hardware status, but the remote graphical console and ISO image mounting are available only with the advanced one. Without it, reinstalling the system means a site visit.
Related reading
HPE ProLiant DL320 Gen11: review of the single-socket 1U server
HPE ProLiant DL320 Gen11 review: one Xeon Scalable with up to 60 cores, 16 DDR5 slots, PCIe 5.0, iLO 6. When one socket pays off better than two and what to compare it with.
Dell PowerEdge T150, T350, R250 and R350: how to choose an entry-level server
How Dell PowerEdge T150, T350, R250 and R350 differ: tower or rack, 4 or 8 drives, prices from 13.8 million UZS. Where people go wrong with the controller and hot swap.
How a server differs from a regular computer, and when a PC or NAS is enough for an office
Xeon or EPYC, ECC memory, hot-swap drives, two power supplies, iLO/iDRAC: how a server differs from a PC and when a NAS is enough. Prices as of November 2026.
How to choose a UPS for a server and server room: calculating power and runtime
How to choose a UPS for a server room: VA and W, a 20–30% margin, real consumption from HPE Power Advisor and iLO, online UPS, runtime and a calculation example for 1.6 kW.




