Network adapter selection 10/25/40G: transceivers and DAC, compatibility
Updated
In brief. Network speed is set not by the card on its own but by the chain “card — module or cable — switch port”: 10G lives in the SFP+ connector, 25G in SFP28, 40G in QSFP+. In the Servix catalog as of November 2026, a 4-port gigabit card costs from 2,875,294 UZS, a dual-port 10G SFP+ card from 4,097,294 UZS, 25G SFP28 from 5,031,764 UZS, 40G QSFP+ is on request, and a 16G FC HBA from 10,782,352 UZS. Inside a rack the cheapest way to connect is a DAC cable: a one-meter cable costs 249,000 UZS, a three-meter one 299,000 UZS.
Request network card selection → — send us the models of your servers and switches and the distances between racks, and an engineer will put together a list of cards, modules and cables that are sure to work together.
Quick links: what speed you need · SFP+, SFP28, QSFP+ and BASE-T · PCIe, OCP3 or FLR · DAC, AOC or optics · module compatibility · cards in the catalog with prices · FC HBA for SAN · ready-made kits
What speed you actually need
A mistake in either direction costs money: gigabit where ten gigabit is needed hits the ceiling at the very first backup, and 25 gigabit for a file server for ten people is money that will never pay off.
- 1 GbE. Management, a standby link, a small office server, IP telephony. Four-port cards such as Intel I350-T4 (2,875,294 UZS) are bought for the number of ports, not for speed.
- 10 GbE. The working standard for connecting servers to the core and to storage systems over iSCSI. A single backup stream easily takes up an entire gigabit, so 10G is not headroom but normal density for 2026.
- 25 GbE. Virtualization clusters, hyperconverged setups, storage systems with a flash pool. It costs only slightly more than 10G but gives two and a half times the bandwidth; cards such as HPE 640SFP28 work at both 10 and 25 gigabits, so migration is smooth.
- 40 GbE and above. Backbones between switches, nodes for analytics and AI, replication between sites. For server access this is usually overkill.
A practical rule: look not at the application's peak bandwidth but at how long the backup window takes. If a full 4 TB backup does not fit into one night, the network is the bottleneck, and the fix is moving to 10 or 25 gigabit, not replacing drives.
Connectors: SFP+, SFP28, QSFP+ and twisted pair
The connector determines which modules and cables will physically fit into the card. This is the first thing checked before ordering.
Connector | Speed | What plugs in | Where it is used |
|---|---|---|---|
SFP+ | 10G (and 1G with the appropriate module) | SR, LR, DAC, AOC modules | the main format of server cards and switch uplinks |
SFP28 | 25G, compatible with 10G | 25G SR modules, 25G DAC | new-generation cards, network core |
QSFP+ | 40G, splits into 4 × 10G | QSFP+ SR4, DAC, “breakout” cable | backbones, dense connections |
QSFP28 | 100G, splits into 4 × 25G | QSFP28 SR4, LR4, DAC | network core and data center |
BASE-T (RJ-45) | 1G, 10G | standard Category 6a twisted pair | where there is no fiber, over short distances |
The modules and DAC cables themselves now have their own section in the catalog: SFP, SFP+, SFP28 and QSFP optical modules — 74 items, from 170,600 UZS for a gigabit SFP up to QSFP28 100G. It also has SR and LR for all speeds, single-fiber WDM for 3–120 km and DAC for 1–5 meters.
A separate note on 10GBASE-T: cards such as Intel X540-T2 (price on request) and Intel X710-T4 (7,907,058 UZS) are convenient because they work over ordinary twisted pair, but they run hotter and have slightly higher latency than optics. For a rack where everything is close together, SFP+ with a DAC cable is cheaper and more reliable.
Form factor: PCIe, OCP3 or FLR
The same chip is sold in three versions, and they are not interchangeable.
- PCIe. A standard expansion card in a slot. Universal, but it takes up a slot that may be needed for a RAID controller or GPU. Example — HPE 560SFP+ (price on request).
- OCP 3.0. A compact module in a dedicated bay: PCIe slots stay free, and replacement does not require disassembling the server. Examples — HPE Broadcom 57412 OCP3 (price on request) and Dell 57414 25G OCP3 (5,031,764 UZS).
- FLR and rNDC. Proprietary formats of the previous generation: HPE FlexibleLOM (HPE 562FLR, 5,031,764 UZS) and Dell rNDC (Dell X540/I350 rNDC, price on request). They fit only their own platforms — an FLR card from Gen9/Gen10 will not fit a Dell, and vice versa.
Before ordering, check the server specification to see which bay is free: an OCP3 card will not physically fit a server without an OCP bay, and an FLR card will not work in another vendor's server.
DAC, AOC or optics: chosen by distance
Connection type | Transmission distance | When it is chosen | Example and price |
|---|---|---|---|
DAC, passive copper | up to 3–5 m | server and switch in the same rack | DAC 1 m — 249,000 UZS, DAC 3 m — 299,000 UZS, DAC 5 m — 718,823 UZS |
QSFP+ → 4 × SFP+ “breakout” DAC | up to 3–5 m | connect four servers to one 40G port | 40G QSFP+ to 4 × SFP+ — price on request |
Vendor-branded DAC | up to 3–7 m | the switch strictly checks modules | HPE X240 10G SFP+ DAC — price on request |
SR optics (multimode) | 10G — up to 300 m over OM3 and 400 m over OM4; 25G — 70 and 100 m | between racks and floors | patch cords OM4 5 m — 2,156,470 UZS, OM4 15 m — 2,156,470 UZS |
LR optics (single-mode) | up to 10 km | between buildings and sites | SFP+ LR 10 km modules — from 429,000 UZS, SFP28 LR — from 950,600 UZS, QSFP28 LR4 — from 7,469,700 UZS |
The modules and DAC cables themselves now have their own section in the catalog: SFP, SFP+, SFP28 and QSFP optical modules — 74 items, from 170,600 UZS for a gigabit SFP up to QSFP28 100G. It also has SR and LR for all speeds, single-fiber WDM for 3–120 km and DAC for 1–5 meters.
Inside a rack, DAC wins on every count: it is cheaper than a pair of modules with a patch cord, needs no connector cleaning and barely heats up. As soon as the distance exceeds 5 meters or the route goes through another floor, only optics will do, and the fiber type (OM3, OM4, single-mode) determines the maximum length.
Compatibility: why a module “won't come up”
The most common problem when buying on your own is that the switch or card sees the module but the port does not come up. The causes are always the same.
- Vendor coding. The module stores a manufacturer code, and some equipment accepts only its “own” modules. Cisco and HPE are the strictest about this; on Cisco it can be bypassed with a command that allows third-party transceivers, but this removes warranty support for the port.
- Intel cards. The X520 and X710 series have historically been picky about modules: some firmware versions work only with Intel modules or with modules explicitly allowed in the driver. Check this before buying if you are getting the card and the modules from different suppliers.
- Speed and type on both sides. An SFP28 card will bring up a link with an SFP+ module at 10 gigabits, but 25G on both sides requires 25G modules, 25G ports and the right fiber.
- FEC at 25G. At 25 gigabits, forward error correction negotiation between the card and the switch sometimes has to be set manually — if the link is “flapping”, that is where to look.
The practical conclusion: cards, modules and cables are cheaper and faster to buy as one kit for a specific “server — switch” pair rather than separately from different suppliers. We do this check before shipment.
Catalog: cards by speed with prices
Gigabit (1 GbE) — management, standby links, affordable port density:
- Broadcom 5720 1G 2-port PCIe — price on request, Dell 5720 1G 4-port rNDC — price on request
- Intel I350-T4 1G 4-port PCIe — 2,875,294 UZS, Broadcom 5719 1G 4-port PCIe — 2,875,294 UZS, HPE 331T 1G 4-port PCIe — 2,875,294 UZS
- HPE Intel I350-T4 1G 4-port OCP3 — price on request, Dell Broadcom 5720 1G 4-port OCP3 — price on request
10 GbE, SFP+ optics — the main format for servers:
- HPE 530SFP+ 2-port — 4,097,294 UZS and Intel X520-DA2 — 4,097,294 UZS: the most affordable entry into ten gigabit.
- HPE 560SFP+ 2-port — price on request, HPE 562SFP+ 2-port — 5,031,764 UZS, HPE 560FLR 2-port — 5,031,764 UZS, HPE 562FLR 2-port — 5,031,764 UZS.
- HPE X710-DA2 — price on request, Intel X710-DA2 for HPE Gen10 Plus — price on request.
- Four-port Intel X710-DA4 — 7,188,235 UZS (the catalog has two listings for this model: the second one).
- OCP3: HPE Broadcom 57412 — price on request, Dell 57412 — price on request, HPE Broadcom 57416 OCP3 — 5,750,588 UZS.
10 GbE over twisted pair (BASE-T) — when there is nowhere to run fiber: Intel X540-T2 — price on request, Intel X710-T4 4-port — 7,907,058 UZS, the combined Dell X540/I350 rNDC — price on request.
25 GbE (SFP28) — clusters and flash storage systems: Dell 57414 25G OCP3 — 5,031,764 UZS, HPE 640SFP28 10/25G — 5,750,588 UZS, HPE 631SFP28 10/25G — 5,750,588 UZS.
40 GbE (QSFP+) — backbones: HPE 544+QSFP 10/40G — price on request, Intel XL710-QDA2 40G — price on request.
The whole section — network card catalog and prices, cables and patch cords — other components.
FC HBA: a separate story for SAN
Fibre Channel is not Ethernet: a different fabric, different switches, different adapters. An FC card is chosen when the storage system connects over FC rather than iSCSI.
- 16 Gbit: Dell QLogic QLE2692-SR 2-port — 10,782,352 UZS, Dell Emulex LPe31002 2-port — 10,782,352 UZS, HPE SN1200E 2-port — 12,220,000 UZS.
- 32 Gbit: Dell Emulex LPe32002 2-port — 14,376,470 UZS, HPE SN1600Q 2-port — 15,957,882 UZS.
The rule is simple: two adapters per server and two independent fabrics, otherwise FC loses its point. Which to choose — FC, iSCSI or SAS — is covered in the guides to the arrays HPE MSA 2060 and 2062 and Dell PowerVault ME5.
Ready-made kits
- Two servers and a storage system over 10G iSCSI — price on request. Two HPE 562SFP+ cards (5,031,764 UZS each) and four cables DAC 3 m. Everything is in one rack; no optics needed.
- A 25G virtualization cluster — price on request. Three HPE 640SFP28 and six DAC 1.5 m: two links from each node to different switches.
- Connection to a 16G FC fabric — 28,752,940 UZS. Two HPE SN1200E and two patch cords OM4 5 m. The modules in the FC adapters are already installed.
The amounts are for the network part; switches are priced separately — models and prices are in the selection Aruba Instant On for the office and in the guide to 24- and 48-port switches.
What to clarify before ordering
- Whether a PCIe slot of the required length is free and whether there is an OCP3 bay — this is determined by the specification of the particular server.
- Which modules your switch accepts and whether you will need to allow third-party transceivers.
- Fiber type on the route: OM3 and OM4 give different maximum lengths, and at 25 gigabits the difference is especially noticeable.
- Whether you need modules at all: they are already built into a DAC cable, and FC adapters ship with modules.
- Lead time: made to order, usually 2–3 weeks; the exact lead time is stated in the invoice.
A detailed technical breakdown of formats and transceivers is in the guide network cards and transceivers: 10G, 25G, 40G. We will select and verify a kit for your servers and switches — write to us.
Sources
Other Servix collections
- Server configurations and prices
- Server for 1C: configurations and prices
- How to choose a Dell PowerEdge
- HPE ProLiant Gen11: configurations and prices
- FortiGate by number of employees
- Dell PowerVault ME5 storage systems
- HPE MSA 2060 and 2062 storage systems
- Aruba Instant On for the office
- Xeon and EPYC server processors
- Drives and RAID controllers
- Server for video surveillance
- Dell PowerVault reference guide
- RAID controller reference guide
- HPE MSA reference guide
- Server for virtualization
- File server and backup