Wi-Fi in a warehouse: racks, metal and data collection terminals
Servix technical team · Updated
In brief. Warehouse Wi-Fi is planned not by floor area but by the aisles between racks: metal and goods block the signal so much that the neighboring aisle becomes a separate coverage zone. Access points are mounted along the aisles at a height of 4–6 meters, not in a grid under the ceiling. Data collection terminals often work only on 2.4 GHz and require properly configured roaming; otherwise the forklift driver loses the session at every turn. The loading dock and yard need an outdoor access point: Aruba Instant On AP17 — 3,850,000 UZS. The access point for the main floor is the AP25 for 5,900,000 UZS, and a PoE switch for them costs from 6,300,000 UZS.
The office rule of “one access point per 80–120 square meters” cannot be applied in a warehouse: where in an open-plan office the signal spreads freely, in a warehouse it runs into a rack full of metal and goods. We explain how to calculate coverage, where to mount access points and why data collection terminals behave differently from laptops.
How a warehouse differs from an office
- Racks are walls. A row of pallets with metal parts, cans, liquids or foil packaging weakens the signal almost as much as a load-bearing partition. And the picture changes during the day: in the morning the aisle is empty, by evening it is packed with goods, and the coverage zone shrinks.
- Height. A ceiling of 8–12 meters means that an access point under the ceiling shines “at the floor” from a great distance, and an omnidirectional antenna wastes power in directions where nobody is.
- The clients are different. Data collection terminals, scanners and forklift onboard computers are not laptops: weak antennas, often only the 2.4 GHz band, and constant movement between zones.
- The cost of downtime is higher. When a data collection terminal loses connection, receiving and shipping stop, rather than an employee just getting annoyed.
Ceiling height and where to mount access points
The main rule: access points are mounted along the aisles, not in an even grid under the ceiling. The racks define the coverage geometry, and the signal should travel along the aisle, not through the rows.
- The optimal mounting height is 4–6 meters. Any higher, and the signal reaches the terminal at a sharp angle and the level drops; any lower, and the access point easily gets hit by a forklift.
- On ceilings higher than 8 meters, access points with directional antennas oriented along the aisle are installed. An omnidirectional access point under a 10-meter ceiling performs noticeably worse than the same access point at 5 meters in the aisle.
- Between tall racks, the signal from the neighboring aisle hardly helps: plan for each aisle to be served by its own access point or a pair of access points at the ends.
- Receiving, shipping and packing areas are a separate story: there is open space and a high density of people and equipment, and they need their own access point.
What blocks the signal the most
In order of impact, from worst to tolerable: metal racks and wire mesh decking, pallets with liquids (water absorbs 2.4 and 5 GHz), foil and metallized packaging, tightly stacked cardboard, plastic. Cold rooms are a separate problem: insulated metal panels act as a shield, and the access point almost always has to be installed inside the cold room.
Practical conclusion: radio planning from a floor plan without accounting for the goods gives errors. If the warehouse is already operating, measurements are taken in a loaded state, not in an empty hall after renovation.
Data collection terminals and roaming
This is what most often trips up projects where the hardware was chosen correctly.
- Band. Many data collection terminals and industrial scanners work only on 2.4 GHz. Coverage must be planned for this band specifically: it has longer range, but there are only three non-overlapping channels (1, 6, 11), and the cells have to be carefully separated.
- Roaming. A forklift driver drives along the aisle and moves from access point to access point. If fast roaming (802.11r, k, v) is not configured, the client clings to the old access point until the last moment and drops the session with the inventory system. A sign of the problem: “the terminal drops off at the far end of the warehouse.”
- Power. Turning the transmitter up to maximum is a typical mistake: the access point “reaches” further than it can hear the terminal's weak antenna. The asymmetry leads to the client seeing the network but being unable to work in it properly.
- A single network. One SSID for the entire site with different VLANs for data collection terminals, the office and guests, not separate networks per zone: otherwise roaming breaks at the boundaries.
How many access points are needed
They are counted by aisles and zones, not by square meters.
- An aisle between tall racks up to 40–50 meters long — one access point per aisle if it hangs in the aisle itself; if longer — two at the ends.
- Open receiving and shipping areas — one access point per zone, taking into account the density of people and equipment.
- The office part of the warehouse is calculated by the usual rules: up to 25–30 active devices per access point. Details are in the guide Wi-Fi 6 or 6E for the office.
- Yard, loading dock, canopy — outdoor access points, one per area with line of sight.
For a 3000 m² warehouse with ten aisles, a receiving area, packing and an office, a realistic figure is 12–16 access points, not “six by floor area.”
Equipment from the catalog
- Main floor and aisles. Aruba Instant On AP25 — 5,900,000 UZS: four streams, 160 MHz channels, handles up to a hundred devices. For less dense zones, the AP22 will do — 4,000,000 UZS.
- Outdoors, loading dock, canopy. Aruba Instant On AP17 — 3,850,000 UZS: the only outdoor model in the lineup. A regular indoor access point must not be installed under an awning — condensation and temperature swings put it out of service within a season.
- Powering the access points. PoE switches: 1930 8G PoE — 6,300,000 UZS for a small area, 1930 48G PoE with a 370 W budget — 19,000,000 UZS for the entire warehouse. A 4x4 access point draws up to 25.5 W, so the budget is calculated by the total, not by the number of ports.
- Core and uplinks. Between buildings and to the server room — fiber: the selection of adapters and transceivers is covered in the roundup network adapters and transceivers.
Kits and prices across the lineup are in the roundup Aruba Instant On for the office, which also explains when the Instant On lineup is no longer enough.
Cold warehouses and outdoors
Freezer rooms and unheated hangars are a special case. A regular access point is designed to operate from 0 °C and above; in a −18 °C room it either does not start or fails from condensation when brought into the warmth. There are two options: an industrial-grade access point with an extended temperature range, or a regular access point placed in a heated thermal enclosure with a sealed cable entry. The antenna is then brought out into the cold room.
For the yard and loading dock, not only moisture protection matters but also lightning protection on the cable: a line running from the building to the outside must be protected, otherwise the very first thunderstorm will take out a switch port.
Common mistakes
- Planning by floor area. Leads to a shortage of access points in the aisles and an excess in open areas.
- Access points under the ceiling at 10 meters. A terminal near the floor receives a weak signal at a sharp angle.
- Maximum power. Creates zones where the network is visible but does not work, and interferes with neighboring access points.
- Measuring in an empty warehouse. Once the racks are filled, the coverage changes completely.
- Different SSIDs per zone. Breaks roaming: the terminal does not switch over automatically.
- One access point for cameras and data collection terminals. Video streams and terminals are better separated into VLANs, and with a high density of cameras, onto different access points as well.
We will design warehouse coverage with an on-site visit: measurements in a loaded state, a placement plan, PoE calculation and equipment selection — write to us or call +998 92 182 11 44. Equipment is in the Wi-Fisection, switches are here.
Questions and answers
How many access points does a 3000 m² warehouse need?
It depends on the geometry, not the area. For ten aisles with tall racks plus receiving, packing and office areas, 12–16 access points is realistic. If you calculate “by area using office norms,” you get six — and half the warehouse will be left without a stable signal in the aisles.
Why does a data collection terminal lose connection even though the network is visible?
Three typical causes: fast roaming is not configured, and the client clings to a distant access point; the access points' power is turned up to maximum, so the terminal hears the network but cannot get through in return; coverage was planned for 5 GHz, while the terminal works only on 2.4 GHz.
Can a regular access point be installed outdoors under a canopy?
No. Even under an awning the access point is exposed to condensation and temperature swings, and its lifespan is measured in one season. For outdoors, choose a model in a protected enclosure — for example, the Aruba Instant On AP17 — and always install lightning protection on the cable leaving the building.
Is Wi-Fi 6 enough, or is 6E needed?
For a warehouse, Wi-Fi 6 is almost always enough. The 6 GHz band has a shorter range and passes through obstacles worse, and data collection terminals do not support it. Wi-Fi 6E makes sense in the office part, where there are many modern clients and the airwaves are congested.
Related reading
Wi-Fi 6 or Wi-Fi 6E for the office: what to choose and how many access points you need
How Wi-Fi 6E differs from Wi-Fi 6, how many access points an office needs, what to consider regarding PoE and the 6 GHz band in Uzbekistan. A breakdown of Aruba Instant On and FortiAP models.
HPE Aruba Instant On: enterprise Wi-Fi without a controller
HPE Aruba Instant On access points: deployment without a controller, guest network, PoE, calculating the number of access points. Where the solution fits and where the higher-end lineup is needed.
Office switch with 24 and 48 ports: Cisco 9200 and C1000, Aruba 1930, FortiSwitch
How many ports and how much PoE an office with 20, 50 and 100 workstations needs; comparison of Cisco Catalyst 9200 and C1000, HPE Aruba Instant On 1930 and FortiSwitch with prices in UZS. Tashkent.
How to choose an SFP module for a Cisco, HPE Aruba, Huawei or Juniper switch
Choosing SFP, SFP+, SFP28 and QSFP28 for Cisco, HPE Aruba, Huawei and Juniper: part number, standard, transmission distance, fiber, BiDi, flashing and a table of Fibreon compatible equivalents.



