Skip to content

Dear customers! Please send orders and inquiries to [email protected] or to Telegram @servix_uz instead of calling by phone: due to the high workload, the operator cannot answer all incoming calls.

Servix

Wi-Fi 6 or Wi-Fi 6E for the office: what to choose and how many access points you need

Servix technical team · Updated

In brief. Access points are counted by the number of active devices, not by floor area: up to 25 clients per 2×2 access point and up to 50 per 4×4 access point; an office of 40 people needs at least three or four access points. Wi-Fi 6E adds the 6 GHz band, but paying extra for the third radio is worthwhile only where the airwaves are congested and the band is permitted by the regulator; otherwise a 6E access point works as Wi-Fi 6. Aruba AP21 and AP25 suit a small office; with a FortiGate on the perimeter, FortiAP 231G or 431G are chosen.

Wi-Fi 6 or Wi-Fi 6E for the office: the short answer

Wi-Fi 6 is enough for most offices in Tashkent: the access points are cheaper, and all devices understand the 2.4 and 5 GHz bands. Wi-Fi 6E adds the 6 GHz band (5925–⁠7125 MHz) and is justified where the airwaves are congested — open space for 80+ people, meeting rooms, warehouses with terminals — and only if the band is permitted in Uzbekistan. Without that, a 6E access point works as Wi-Fi 6 but costs two to three times more.

Parameter

Wi-Fi 6 (802.11ax)

Wi-Fi 6E (802.11ax, 6 GHz)

Frequency bands

2.4 and 5 GHz

2.4, 5 and 6 GHz

When to choose

office of up to 50–⁠80 people, normal load

congested airwaves, many clients with a 6E module

Requirement

—

6 GHz band permitted by the regulator

In the Servix catalog

Aruba AP22 — 4,000,000 UZS, AP25 (4×4) — 5,900,000 UZS

FortiAP 231G — 11,434,500 UZS, FortiAP 431G — 17,500,000 UZS

The most common mistake when buying office Wi-Fi is counting access points by floor area. “A hundred square meters, one is enough” — that is how you choose a home router, not a network in which fifty laptops, phones and cameras work at the same time. Device density matters more than area: an access point that reaches the far corner will still choke if forty clients connect to it. Let's look at how to choose based on what actually matters.

How the generations differ

Wi-Fi 5 (802.11ac) works only in the 5 GHz band (plus 2.4 GHz on the second radio) and serves clients one at a time. With a dozen active devices per access point, this is already noticeable.

Wi-Fi 6 (802.11ax) added two things that matter specifically in an office. OFDMA divides the radio channel into subchannels, so the access point serves several devices in one time slot rather than strictly one at a time — the more clients, the bigger the gain. Target Wake Time lets a device sleep between communication sessions: it noticeably extends battery life for phones, tablets and sensors.

Wi-Fi 6E is the same 802.11ax, but with access to the additional 6 GHz band. The main advantage is not speed but clean airwaves: in 2.4 and 5 GHz you share frequencies with your neighbors in the business center, while 6 GHz is still almost empty, and wide non-overlapping channels are available there.

Important: the 6 GHz band and permits

Before buying equipment for the sake of 6 GHz, check its regulatory status. Different countries have opened this band in different ways: in some it is permitted without a license only for indoor use, in others part of the band is reserved for mobile communications, and in others its use requires a separate permit. The current status for Uzbekistan is confirmed with the State Commission on Radio Frequencies.

Practical conclusion: a Wi-Fi 6E access point is not useless even if 6 GHz cannot be used — it remains a full-fledged Wi-Fi 6 access point in the 2.4 and 5 GHz bands. But paying extra for the third radio makes sense only when you will be able to turn it on.

How many access points are needed

You need to count from the number of simultaneously active devices, not from square meters. Guidelines for office workloads:

  • up to 25 active devices per access point — comfortable work with documents, email, video calls;
  • 25–⁠50 — the working limit for entry-level 2×2 access points; video conferences will start to lag;
  • over 50 — you need a 4×4 access point or more access points with lower power and proper channel separation.

Count two to three devices per employee: a laptop, a phone, sometimes a tablet or headset. For an office of 40 people, that is 80–⁠120 clients, meaning at least three or four access points, not one “powerful” one. Account for meeting rooms separately: there may be a dozen devices plus a video conferencing system in 10 square meters.

It is better not to turn the transmitter power all the way up. The access point “reaches” further than it can hear the phone's response, and clients cling to a distant access point instead of a nearby one. In dense offices, it is better to install more access points at lower power.

What is in the catalog

Model

Generation

Antennas

Use case

Aruba Instant On AP21

Wi-Fi 6

2×2

Small office, individual offices, up to 25 devices

Aruba Instant On AP22

Wi-Fi 6

2×2:2

Open space of a small office

Aruba Instant On AP25

Wi-Fi 6

4×4

High density: open-plan office, meeting rooms

FortiAP 231G

Wi-Fi 6E

2×2 per radio

Office managed from FortiGate, three bands

FortiAP 431G

Wi-Fi 6E

4×4

Dense scenarios, conference rooms

FortiAP 221E

Wi-Fi 5

2 radios

Budget coverage, undemanding tasks

For outdoors — canopies, parking lots, warehouse yards — you need an access point in a protected enclosure, for example the Aruba Instant On AP17. A regular indoor access point must not be installed under an awning: condensation and temperature swings put it out of service within one season.

What to manage from: the cloud or the firewall

There are two fundamentally different approaches, and choosing between them matters more than choosing a specific model.

Instant On — access points are managed from the cloud or a mobile app, without a controller and without a management subscription. It can be deployed in an evening and is understandable to an administrator of any skill level. The limitation is that the feature set is designed for small businesses: segmentation is simple, and there is no deep integration with security policies.

FortiAP is managed from the FortiGate firewall as part of a unified fabric. This is more complex to set up initially, but it provides what entry-level cloud solutions lack: policies for wireless clients are written in the same place as for wired ones, guest network traffic passes through the same inspections, and logs are collected in one place. If a FortiGate is already on the perimeter, access points from the same vendor spare you a zoo of management panels. How to choose the firewall itself is covered in the article on choosing a FortiGate.

What people forget: power and cabling

Access points are powered over twisted pair via PoE, and it is easy to get this wrong. Wi-Fi 6 access points, and especially 6E access points with three radios, require PoE+ (802.3at), not basic PoE. The switch must be chosen by the total power budget: eight access points at 25 W each is 200 W for Wi-Fi alone, plus headroom for IP phones and cameras. Suitable models are in the switchessection.

The second point is the cable. Category 5e is enough for gigabit, but Wi-Fi 6 access points can deliver more, and the bottleneck moves from the air to the wire. If the network is being built from scratch, plan for Category 6.

The third is placement. An access point on a wall behind a cabinet or in a suspended ceiling above an air duct loses a noticeable part of its coverage. The right place is the ceiling in the center of the service area, with no metal or thick floor slabs in the way.

A short algorithm

Count the simultaneously active devices and divide by 25 for 2×2 access points or by 50 for 4×4 — you get the minimum number of access points. Check whether the switch can handle their total PoE power. Decide whether to manage from the cloud or from the firewall. And only then choose between Wi-Fi 6 and 6E: the third band costs money and makes sense where the airwaves are really congested and its use is permitted.

To select a set of access points, a switch and licenses for a specific floor plan, write to us. Equipment is in the Wi-Fisection.

Related roundups and tools: Aruba Instant On for the office, PoE calculator.

Sources

Questions and answers

Can access points of different generations be mixed?

In one network — yes, if they are from the same vendor and managed from one panel. But the client chooses the access point itself, and a device that has latched onto an old Wi-Fi 5 access point next to a new Wi-Fi 6 one will not get the benefits of the new standard. It is more reasonable to install one generation within a zone and move old access points to the periphery — warehouse, corridors, utility rooms.

Is a separate controller needed?

For a small and medium office — no. Instant On solutions are managed from the cloud, FortiAP from an existing firewall. A separate hardware controller is justified with dozens of access points with seamless roaming and complex policies.

What does WPA3 provide and should it be enabled?

WPA3 closes known weaknesses of WPA2, including handshake capture for subsequent password cracking. It is worth enabling, but in mixed mode: some older devices — printers, scanners, industrial sensors — do not support WPA3 and simply will not connect to a network where it is mandatory.

Related reading